1、專用底盤由發動機、車架、行走機構、轉向機構等組成。發動機為直列4缸水冷、自然吸氣發動機，帶全程調速器，運行平穩，具有熱效率高、比油耗低、排放污染少等特點。由于臺車行駛速度低，綜合考慮作業安全性和經濟性，車架采用剛性連接式，不設懸架機構，輪胎選用高負荷實心橡膠輪胎。
Special chassis from the engine, frame, running gear, steering mechanisms and other components. Water-cooled inline four-cylinder engine, naturally aspirated engine with full governor, smooth operation, high thermal efficiency, low specific fuel consumption, less emissions pollution. Due to the low trolley travel speed, considering the operational safety and economy, frame rigid connection type, no suspension mechanism, tire selection of high load solid rubber tires.
2、行走方式為液壓驅動，直接選用進口馬達與減速機一體化的內藏式行走減速機，設有快慢速兩擋行駛速度，滿足車輛在不同環境下行駛要求。在坡道行駛時行走機構具有自制動功能，同時還設離合裝置，在出現故障時方便拖行。
Walking the way for hydraulic drive, direct selection of imported motor and gear reducer integrated Built walking with two block fast slow speed, the vehicle meets the requirements in different environments. When the ramp with travel agencies with self-braking function, but also set off device, in case of failure to facilitate towing.
3、工作裝置由回轉臺、工作臂架、伸縮軟鏈等組成。所有鉸接點均采用自潤滑軸承，降低保養要求，所有需要潤滑的點都設有加油口，可以方便地進行保養。為方便維修保養，所有油缸、管路外置，管路和電纜均有保護拖鏈。
Working device by turret, working jib, retractable soft chains and other components. All hinge points are self-lubricating bearings, reducing maintenance requirements, all require lubrication points are equipped with refueling port, you can easily carry out maintenance. To facilitate maintenance, all cylinders, external piping, piping and cable have protection towline.
4、三維全旋機構，回轉體體積小，只需很少液壓流量就可以旋轉很大角度，帶來的問題就是旋轉速度很難控制。為解決轉速控制問題，在液壓系統單獨設置微量泵，微量泵由專用電機驅動，可保證轉速恒定，從而為回轉系統提供穩定的流量。
Three-dimensional full rotation mechanism, slewing body is small, just a few large hydraulic flow angle can be rotated to bring the problem is difficult to control the rotation speed. To solve the speed control problems in the hydraulic system set up separate micro pump, micro pump driven by a dedicated motor can ensure constant speed, thus providing a stable flow of rotating systems.
5、柔性夾緊裝置，當油缸伸出時，將軟帶一端與彈簧固定，一端與伸縮臂固定，然后回縮油缸，夾緊風管。當油缸縮回時，軟帶松弛，帶扣脫落，無需人工輔助，夾緊裝置即可隨大臂自動收回。
Flexible gripping means, when the cylinder extends, the flexible tape is fixed at one end of the spring, one end of the telescoping arm is fixed, and the cylinder is retracted, the clamping duct.When the cylinder is retracted, the soft belt slack, buckle off, without human assistance, clamping devices can automatically recover with the big arm.
6、安全裝置。設有電動應急系統，當底盤發動機和主泵液壓系統出現故障時，借助以12V底盤電源為動力的微型組合式液壓泵站，將工作裝置降至行駛狀態。舉升作業裝置下方設有檢測裝置，以防止誤操作時舉升機構與動臂機構碰撞，造成損害。
With electric emergency systems, engine and chassis when the main pump hydraulic system failure, with the chassis, power supply to 12V powered miniature modular pump stations, traveling down to the working device status. Below the lifting device has a detection device operation, lifting mechanism to prevent the misuse of collision with the actuator, causing damage.