提升鏈條在導軌式升降貨梯上起著至關重要的作用，所以保養好提升鏈條可以延長導軌式升降貨梯的使用壽命，保證其使用安全性。下面就給大家詳細介紹一下貨梯提升鏈的維護方法。

1、鏈輪裝在軸上應沒有歪斜和擺動，不允許有摩擦鏈輪齒側面現象，如果兩輪編移過大容易產生脫鏈和加速磨損，在更換鏈輪時必須注意檢查和調整偏移量。
Zhejiang freight elevator sprockets on the shaft should not skewed and swing, does not allow the sprocket side friction phenomenon, if an offset is too large rounds off the chain and prone to accelerated wear, when replacing the sprocket must be careful to check and adjust the bias shift.

2、起重鏈條的松緊度應適宜，太緊增加功率消耗，軸承易磨損；太松鏈條易跳動和脫鏈。鏈條的松緊程度為：從鏈條的中部提起或壓下，兩鏈輪中心距的約為2%-3%。
Tightness lifting chain should be appropriate, too tight increase in power consumption, bearing wear; the chain is too loose and easy to beat off the chain. Tightness of the chain as follows: Lift or pressure from the middle of the chain, the two sprocket center distance of about 2% -3%.

3、新的起重鏈條過長或經使用后伸長，難以調整，可看情況拆去鏈節，但必須為偶數。鏈節應從鏈條背面穿過，鎖片插在外面，鎖緊片的開口應朝轉動的相反方向。
The new lifting chain is too long, or by the use of post-elongation, it is difficult to adjust, you can remove the link to see the situation, but it must be even. Should pass through the back of the chain link, the locking plate is inserted on the outside, the opening of the lock piece to be rotated toward the opposite direction.

4、浙江貨梯http://m.st-image.cn/鏈輪磨損嚴重后，應同時更換新鏈輪和新鏈條，以保證良好的嚙合。不能只單獨更換新鏈條或新鏈輪，否則會造成嚙合不好加速新鏈條或新鏈輪的磨損，鏈輪齒面磨損到一定程度后應及時翻面使用。
Zhejiang freight elevator sprockets badly worn, it should also replace the new sprocket and new chain, to ensure good engagement. Not just a single new replacement chain or sprocket, otherwise it will create a new chain or meshed well accelerate new sprocket wear, sprocket tooth wear to a certain extent should be used upside down.

5、浙江貨梯舊的起重鏈條上不能與部分新鏈條混合使用，否則容易在傳動中產生沖擊，拉斷鏈條。
Zhejiang old freight elevator lifting chain on the chain can not be part of the new mixed-use, or prone to shocks in the drive, and pull off the chain.

6、浙江貨梯起重鏈條在工作中要記得及時加注潤滑油。而潤滑油則必須進入滾子和內套的配合間隙，以便改善工作條件，以減少磨損。
Zhejiang freight elevator lifting chain at work in time to remember filling oil. The lubricant must enter the roller and the inner sleeve with the gap in order to improve working conditions in order to reduce wear.